Products
Septic pump systems
Item no.: N/AOur septic pump systems are manufactured using fiber-reinforced composite material, a strong, durable and lightweight material that ensures a long operational lifespan and easy installation. The systems comprise a discharge system and a pump system, both of which are integral components.
- The discharge system consists of a Ø40 mm pressure discharge pipe complete with joint fittings, excluding the PEL hose
- The pump system features a single pump with a level float for start-stop operation, a swing check valve, an outlet hose, fittings and a mounting FRP profile
Our pressure infiltration systems, like our septic pump systems, are also made from fiber-reinforced composite, ensuring high strength, longevity and ease of installation.
- Fiber-reinforced composite material with great strength and long life-cycle
- Low weight and easy mounting
- Resistant against corrosion
- Durability
Comes with
Precipitation tanks can be further reinforced to withstand groundwater pressure, heavy traffic loads and soil pressure.
Sizes and Specifications
| Diameter | Volume | Types | Height | Inlet height | Discharge zone |
|---|---|---|---|---|---|
| 2300 mm | 8,0 m³ | 20 PE | 2900 mm | 1900 mm | 8 x 16 m |
| 2300 mm | 10,0 m³ | 25 PE | 3400 mm | 2400 mm | 10 x 16 m |
| 2300 mm | 12,0 m³ | 30 PE | 3900 mm | 2900 mm | 12 x 16 m |
| 2800 mm | 14,0 m³ | 35 PE | 3100 mm | 2100 mm | 14 x 16 m |
| 2800 mm | 16,0 m³ | 40 PE | 3400 mm | 2400 mm | 16 x 16 m |
| 2800 mm | 18,0 m³ | 45 PE | 3700 mm | 2700 mm | 18 x 16 m |
| 2800 mm | 20,0 m³ | 50 PE | 4000 mm | 3000 mm | 20 x 16 m |
Extra equipment
Item no.: N/A FRP Shafts without Sleeves
Learn More
×
FRP Shafts without Sleeves
FRP shafts without sleeves are commonly employed for extending wells. These shafts are manufactured using glass fiber-reinforced polyester, a corrosion and chemical-resistant material.
| Diameter | Height |
|---|---|
| 315 mm | 500 mm |
| 315 mm | 1000 mm |
| 315 mm | 1500 mm |
| 315 mm | 2000 mm |
| 425 mm | 500 mm |
| 425 mm | 1000 mm |
| 425 mm | 1500 mm |
| 425 mm | 2000 mm |
| 580 mm | 500 mm |
| 580 mm | 1000 mm |
| 580 mm | 1500 mm |
| 580 mm | 2000 mm |
| 780 mm | 500 mm |
| 780 mm | 1000 mm |
| 780 mm | 1500 mm |
| 780 mm | 2000 mm |
| 900 mm | 500 mm |
| 900 mm | 1000 mm |
| 900 mm | 1500 mm |
| 900 mm | 2000 mm |
Item no.: N/A High water level alarms
Learn More
×
High water level alarms
High Water Level Alarms can be installed in e.g., rainwater tanks, collection tanks, pumping wells, precipitation tanks, etc.
The alarm will signal at the pre-set height.
The level float is on top of the water and when it reaches the level switch, the alarm will signal.
Comes with:
- High water level alarm SPHA-2
- Level float
- Level switch
- Mounting equipment
- 4 screws
- Strips for mounting of level float
Installation
Lower the level float down until reaching the wanted alarm level. Mount on the inside of the access shaft. The level float can be mounted on the service step for easy hoisting/lowering in case of service or adjustments.
| Types | Width | Height | Depth |
| SP-HA2 | 145 mm | 170 mm | 120 mm |
Technical Diagram
Electrical Diagram
Item no.: N/A Septic tank alarms – Lokaset 20
Learn More
×
Septic tank alarms – Lokaset 20
Lokaset 20 septic tank alarm is a full alarm system for supervision of overflows in precipitation and collection tanks.
Lokaset 20 is a conductively controlled safety device consisting of a sensor unit and a control box. When the sensor comes in contact with a conductive fluid, the control box will put out a signal: turning on the red indicator lamp, buzzing starts, and disconnecting the alarm relay. By pressing the alarm receipt button, the buzzing will be turned off. The indicator lamp will continue to light up, and the relay will still be disconnected until the alarm is removed i.e., the sensor is no longer in contact with the fluid. The alarm is equipped with a 4-5 seconds delay to avoid unnecessary alarm because of splashes.
SET/LV sensor: The sensor and belonging cable are equipped with a fault-finding device that can localise breakdowns in the sensor circuit. The device is powered by 230VAC mains through a connecting cable with a standard plug. When the device is in on-mode, the alarm relay is in alarm setting i.e., disconnected. When the device is powered, a green light will turn on.
NOTE! The alarm must not be used for installations in areas with risk of environmental damages. SET/LV or SET/L sensor must not be installed in areas with risk of environmental damages.
It is not recommended to install SET/LV or SET/L sensor in areas where fumes, gasses, or fluids with possible corroding effects on the sensor are present e.g., aromatic and chlorinated hydrocarbons (PVC), strong bases or acids.
Comes with:
- Control box with indicator
- Indicator light and buzzing alarm
- SET/LV overflow sensor
Benefits:
- Easy to install
- Visual and acoustic signal alarm
- Avoid overflow of tank
- ATEX-certified
| Types | Certification | W x H x D | Supply voltage | Ambient temperature | Compatible sensors |
| SP Lokaset 20 | ATEX | 130 x 80 x 35 mm | 230 V ±10%, 50/60 Hz, 2,8 VA | 0° C…+50° C | SET/LV, SET/L |